Pages Menu
Categories Menu

Posted in Accessories

AUTOTROL Water Meters

 

AUTOTROL TURBINE WATER METER

 

3023532_1 INCH NPT SS TURBINE _070912

1TM-NPT shown

 

 

Flow Sensor Specifications

 

 

 

 

MODEL 1TM

1 inch (25 mm)

MODEL 2TM

2 inch (51 mm)

 

 

 

Flow rate range

0.275 – 35 gpm

(0.0625 – 7.95 m3 /h)

5 – 250 gpm

(1.14 – 56.8 m3/h)

 

 

 

Materials of construction:

Housing

Turbine (Impeller)

Bearings

Shaft

 

 

30% Glass-Filled PPO†

Polypropylene

Polyimide

302 SS

 

 

30% Glass Filled PPO†

Polypropylene

Carbon Graphite

No shaft—thrust bearing

 

 

 

Accuracy

± 3% of reading

± 3% of reading

 

 

 

Pressure Drop

 

Maximum water temp.

Maximum temp.

Maximum pressure

Available cable lengths

 

 

Maximum cable length – kit form

1.5 psi @ 30 gpm

(10.3 kPa @ 7 m3/h)

100°F (38°C)

122°F (50°C)

127 psi (875 kPa)

25, 50 ft

(7.6, 15.2 m)

 

1,000 ft. (305 m)

2.5 psi @ 150 gpm

(17.2 kPa @ 34 m3/h)

100°F (38°C)

122°F (50°C)

100 psi (689 kPa)

25, 50 ft

(7.6, 15.2 m)

 

1,000 ft. (305 m)

 

†    PPO – Polyphenylene Oxide

 

 

ORDERING INFORMATION

 

1033238                        1TM-ESW         1 inch turbine meter with solvent weld PVC adapters

3023532                        1TM-NPT           1 inch turbine meter with 1 inch NPT stainless steel adapter

1034080                        2TM-ESW         2 inch turbine meter with solvent weld PVC adapters

3023536                        2TM-NPT           2 inch turbine meter with 2 inch NPT stainless steel adapter

1033317                        400B418-701     1 inch turbine meter only

1033358                        480B78G1         2 inch turbine meter only

 

 

WATER METER CABLE (ORDER ONE CABLE FOR EACH TURBINE)

 

1033354                        49C25               25 ft cable with Hall Effect sensor

1033355                        49C50               50 ft cable with Hall Effect sensor (NO LONGER AVAILABLE)

 

 

 

INSTALLATION INSTRUCTIONSAutotrol Flow diagram

 

Install the turbine assembly in the water line.  Note the flow direction arrow on the turbine body.  It is highly recommended that there be a length of straight pipe either side of the turbine equal to ten times the pipe diameter.        

 

If installation conditions do not permit this length, a minimum of 12 inches (31 cm) of straight pipe before and after the 2 inch (5 cm) turbine, and 6 inches (15 cm) before and after the 1 inch (2.5 cm) turbine may be sufficient.

  

CAUTIONS

  • AUTOTROL TURBINE WATER METERS ARE NOT TO BE USED AS A UNION.  WATER METERS MUST BE SUPPORTED AT BOTH ENDS.
  • WATER METERS WILL be IDEALLY located in horizontal pipe WITH A LENGTH OF STRAIGHT PIPE EQUAL TO 10 PIPE DIAMETERS on either side.
  • WATER METERS MUST HAVE FLOW oriented from bottom to top when mounted vertically.
  • DO NOT OVER-TIGHTEN THE TURBINE HOUSING ADAPTER NUTS OR YOU MAY DAMAGE THE THREADS

 

 

 

 

3023532_1 INCH NPT SS TURBINE_EXPLODED_070927 

 

1TM-NPT

PART NO. 3023532

The 1TM-NPT Is A 1 Inch Turbine Water Meter With Stainless Steel NPT Adapter Fittings.  The Flow Rate Is .275 – 35 Gpm.  Max Water Temp 100˚F (38˚ C), Max Temp 122˚ (50˚ C) And Max Pressure 127 Psi (875 KPA).

The 1TM-NPT Comes With All Of The Parts Shown.

 Hall Effect Cable Sold Separately.

 

 

 1033238_1in TURBINE PVC EXPLODED VIEW_DESC_060613

 

 

 

1TM-ESW

PART NO. 1033238

The 1TM-ESW Is A 1 Inch Turbine Water Meter With PVC Solvent Weld Adapter Fittings.  The Flow Rate Is .275 – 35 Gpm.  Max Water Temp 100˚F (38˚ C), Max Temp 122˚ (50˚ C) And Max Pressure 127 Psi (875 KPA).

The 1TM-ESW Comes With All Of The Parts Shown.

Hall Effect Cable Sold Separately. 

 

 3023536_2 INCH SS TURBINE_EXPLODED_070927 

 

2TM-NPT

PART NO. 3023536

The 2TM-NPT Is A 2 Inch Turbine Water Meter With Stainless Steel NPT Adapter Fittings.  The Flow Rate Is 5 – 250 Gpm.  Max Water Temp 100˚F (38˚ C), Max Temp 122˚ (50˚ C) And Max Pressure 100 Psi (689 KPA).

The 2TM-NPT Comes With All Of The Parts Shown.

 Hall Effect Cable Sold Separately.

 

 1034080_2 INCH PVC TURBINE_EXPLODED VIEW_DESC_060616

 

2TM-ESW

PART NO. 1034080

 The 2TM-ESW Is A 2 Inch Turbine Water Meter With PVC Solvent Weld Adapter Fittings.  The Flow Rate Is 5 – 250 Gpm.  Max Water Temp 100˚F (38˚ C), Max Temp 122˚ (50˚ C) And Max Pressure 100 Psi (689 KPA).

The 2TM-ESW Comes With All Of The Parts Shown.

 Hall Effect Cable Sold Separately.

 

 

 

 

 1033354_49C25 25ft cable for turbine meter_060623

 

 

49C25

PART NO. 1033354

 The 49C25 Is The Hall Effect Sensor With 25 Ft Of Cable For Use With The Autotrol Turbine Water Meters.

 

 

ORDERING INFORMATION

 

           

PART No.        DESCRIPTION 

      TURBINES

 1033238            1TM-ESW, 1″ Turbine Meter With PVC Fittings

3023532            1TM-NPT, 1″ Turbine Meter With NPT Fittings

1034080            2TM-ESW, 2″ Turbine Meter With PVC Fittings

3023536            2TM-NPT, 2″ Turbine Meter With NPT Fittings

 

                        SENSOR CABLES (1 Required For Each Turbine)

 1033354            49C25, 25 Ft Cable For Turbine Meter

1033355            49C50, 50 Ft Cable For Turbine Meter—DISCONTINUED

 

                        1 INCH TURBINE METER REPLACEMENT PARTS

1033317            1 Inch Replacement Turbine Meter, 400B418-701 

1030541            Gasket 1 Inch

3014631            Turbine Nut 1 Inch for NPT Stainless Steel

1034385            Turbine Nut 1 Inch for ESW PVC

3014557            Adapter 1 Inch NPT Stainless Steel

1030579            Adapter 1 Inch ESW PVC

 

                        2 INCH TURBINE METER REPLACEMENT PARTS

1033358            2 Inch Replacement Turbine Meter, 480B78G1

3030498            Gasket 2 Inch

1030664            Turbine Nut 2 Inch for NPT SS and PVC ESW

3014558            Adapter 2 Inch NPT Stainless Steel

1030666            Adapter 2 Inch ESW PVC